It might be annoying when your furnace abruptly stops operating, particularly in cold weather. It’s beneficial to know how to reset furnace systems before expecting the worst or contacting emergency services. You may often save time and money by restoring regular operation with a simple reset.
This guide describes why furnaces need to be reset, how the reset procedure operates, where reset buttons are located, and when to contact a specialist like MileHi HVAC.
Why Furnaces Need to Be Reset
Safety features included into modern furnaces cause them to immediately shut down when an issue is identified. These shutdowns avoid gas-related risks, electrical damage and overheating. Your furnace may need to be reset for the following common reasons:
- Voltage variations or power outages
- Airflow is restricted by dirty air filters.
- Blocked vents leading to overheating
- Problems with the ignition or flame sensor
You can react swiftly and prevent additional harm to your system by knowing how to reset furnace units correctly.
How to Reset a Furnace Safely
Always put safety first before beginning. Before touching the furnace, use the thermostat to turn it off and wait a few minutes.
Simple Reset Procedure:
- Switch off the circuit breaker or furnace’s power.
- Find the device’s reset button.
- Hold down the button for five to ten seconds.
- Wait for the furnace to restart after releasing the button.
- Turn on the power again and adjust the thermostat.
The furnace reset button, which is typically red or yellow and simple to find, is a common question from homeowners. However pressing it too frequently may point to a more serious problem that needs to be examined by a technician.
Reset button on furnace
Where is the reset button on the furnace is one of the most often asked questions by homeowners. The kind and model of your system will determine the response.
The reset button is usually located:
- Within the blower compartment
- Close to the burner assembly
- Behind a detachable access panel
To prevent damaging internal components, check your user manual or get in touch with an expert if you’re not sure where the reset button on a furnace is located.
Resetting an electric furnace
Electric furnaces frequently have several safety controls and function differently from gas systems. The electric furnace reset button is typically either inside the control panel or next to the heating elements.
An electric furnace can be reset by:
- Turn off the breaker’s electricity.
- Carefully remove the access panel.
- Once, press the reset button.
- Restore power and keep an eye on everything.
Recurrent trips of the electric furnace reset button could be a sign of overheating, electrical issues or malfunctioning parts that need to be fixed by professionals.
You may read How Many Watts Does a Gas Furnace Use?
RV furnaces
Despite being smaller, RV heating systems adhere to the same safety regulations. When traveling in cold weather, many RV owners find it difficult to locate the RV furnace reset button location.
The reset button on the majority of RV models is found:
- In close proximity to the furnace control board
- Behind a cabinet or panel inside
- Near the blower motor housing
While it might be quite useful to know where the RV furnace reset button is, frequent resets indicate problems with the propane supply or airflow, which should not be disregarded.
seeking professional assistance
Furnace system resets are helpful, but they should never be used as a permanent fix. A professional diagnosis is necessary if you don’t know how to reset the furnace?
Get in touch with MileHi HVAC if you observe:
- After being reset, the furnace won’t restart.
- Unusual noises or burning smells
- Frequent shutdowns or brief cycling
- Increasing energy costs without better comfort
Expert technicians can find underlying issues and guarantee the safe and effective operation of your system.
Safety Measures
Use these maintenance suggestions to prolong the life of your furnace and lessen the need for resets:
- Every one to three months, change the air filters.
- Keep registers and vents clear.
- Plan yearly expert checkups.
- Resolve small problems before they become more serious.
Throughout the winter, preventive maintenance from reputable companies like MileHi HVAC keeps your heating system dependable.
Conclusion
Understanding how to reset a furnace is a useful skill, but it is only one part of proper maintenance. While a reset can fix minor glitches, chronic issues require a professional touch. If you are searching for reliable furnace repair in Denver CO, look no further than our expert team. MileHi HVAC provides the professional furnace maintenance and safety inspections needed to keep your home cozy and worry-free. Contact MileHi HVAC to ensure your system runs effectively all winter long.
FAQS
How frequently can my furnace be reset?
Your furnace should only be periodically reset. Regular resets are a sign of an issue that has to be fixed by an expert.
Is it okay to repeatedly click the furnace reset button?
It is not advised to press the furnace reset button more than once or twice in a brief amount of time. Internal components may be harmed by doing this.
Is it possible to reset my furnace without cutting the electricity?
No. To prevent electrical dangers, always turn off the power before attempting any resets.
My electric furnace keeps tripping; why is that?
The electric furnace reset button may be reacting to overheating or airflow obstruction if the system keeps shutting down.
Should I call a professional if my furnace keeps shutting off?
Yes. A certified technician from MileHi HVAC can diagnose the issue safely and prevent costly repairs.
